How To Clean Dyson Vacuum Cleaner

If you have a Dyson vacuum, you know that it’s an investment. Though the upfront cost may be higher than other brands, the quality and performance of a Dyson are unmatched.

To get the most out of your vacuum and keep it running like new, it’s important to clean it regularly.

How To Clean Dyson Vacuum Cleaner

Here’s a step-by-step guide on how to clean your Dyson vacuum cleaner for optimal performance.

Step 1: Remove Your Dyson Filter(s)

Depending on your model of Dyson vacuum, there may be one or two filters that need to be removed and cleaned.

These are generally located near the dustbin. You’ll want to consult your owner’s manual for exact instructions on how to remove and replace your filter(s). 

Step 2: Remove Excess Dust

Once the filter(s) are removed, tap them gently against the side of the garbage can to remove any loose dust particles.

Be sure to do this over a trash can or garbage bag so you don’t make a mess.

Step 3: Rinse Filter(s) With Cold Water

Holding the filter over the sink, rinse it with cold water until the water runs clear.

Avoid using hot water, as this can damage the filter material. Repeat with the second filter, if applicable. 

Step 4: Give It A Firm Shake!

With the filter(s) still wet, give them a good shake (outside you don’t want to make a mess!) to remove any remaining dust or debris. 

Step 5: Leave Them To Dry For 24+ Hours

Once you’ve given them a good shake, set the filter(s) aside in a safe place where they can dry completely before reapplying them to your vacuum.

This process usually takes 24 hours or more, so be patient! 

How To Replace The Filter On Your Dyson Vacuum Cleaner 

1. Locate the Filter – The filter is usually located on the canister, near where the dustbin is attached. On some models, it might be located inside the dustbin itself. 
2. Remove the Filter – On most models, the filter can simply be pulled out. However, some models might have a release button or switch that needs to be activated before the filter can be removed. 
3. Inspect the Filter – Once the filter is removed, take a close look at it. If it looks clean, you can try putting it back in and seeing if that solves the problem. If it’s clogged with dirt and dust, however, it’s time for a new one. 
4. Insert New Filter – Putting in a new filter is as simple as reversing step 2. Simply insert the new filter and make sure it’s properly secured in place.
5. Test’ your Vacuum Cleaner – Once you’ve replaced the filter, it’s time to put your vacuum cleaner to the test! Run it over a section of your floor and see if it’s picking up dirt and debris as it should be. If not, there might be another issue at play (in which case, we recommend taking it to a professional).

How Often Should You Clean Your Dyson Vacuum

Dyson vacuums are known for their powerful suction and innovative design.

However, like all vacuum cleaners, they require regular maintenance to keep them running properly. For best results, the Dyson website recommends that users clean their vacuum’s cyclone assembly after every three months under cold water.

This simple task helps to remove any built-up dirt and debris, keeping the vacuum’s suction strong. In addition, it is important to regularly clean the filters and brushes to prevent them from becoming clogged. 

Can You Wash The Cyclone Part Of A Dyson?

1. First, you need to detach the cyclone from the rest of the vacuum. There should be a release button or catch somewhere on the body of the vacuum that will allow you to do this. Consult your owner’s manual if you’re not sure where it is.
2. Next, use a dry, soft cloth to remove any dust or debris from the surface of the cyclone. Pay extra attention to the area around the inlet ports, as this is where most dirt and debris tend to accumulate.
3. Once you’ve removed all of the visible dirt and debris, it’s time to deep clean the cyclone using an air compressor. Set the compressor to ‘blow’ mode and hold it about 6 inches away from the surface of the cyclone. Move it around so that all areas are evenly cleaned. Do not use ‘airbrush’ mode, as this can damage delicate parts of the cyclone.
4. Finally, reattach the cyclone to the rest of the vacuum and give it a test run to make sure everything is working properly. 

Also, be sure to check your owner’s manual for specific instructions on how often you should clean your Dyson vacuum’s cyclone as well as any other maintenance tips that may be relevant to your model.

How To Fix Loss of Suction In A Dyson

Strong suction is the cornerstone of any good vacuum, and no vacuum has stronger suction than a Dyson.

But even Dysons can have issues from time to time, one of the most common being the loss of suction. Here are some of the most common reasons for the suction loss in a Dyson and how to fix them.

The most common reason for loss of suction in a Dyson is a blockage somewhere in the machine. The first place to check is the pre-motor filter this is located just behind the clear bin assembly on the back of the machine.

If this filter is clogged, it will restrict airflow and reduce suction power. To clean or replace the pre-motor filter, follow these instructions: 

1. Remove the clear bin assembly from the machine by pressing the release button and pulling upwards.
2. Take out the pre-motor filter and tap it gently on the side of a bin to remove any debris. If your filter is damaged or torn, you’ll need to replace it—instructions on how to do that can be found here. 
3. Put everything back together and test your machine to see if the suction has been restored. 
4. If there’s still no improvement, move on to checking/cleaning the post-motor filter—instructions on how to do that can be found here. 
5. Again, test your machine after completing this step to see if the suction has been restored. 
6. If you’re still not seeing an improvement, it’s possible that something is blocking the airflow path between the floor and the cyclone pack (the part of the vacuum where dirt and debris are collected). To check for this, first, detach the hose from where it meets with the base of your machine (instructions on how to do that can be found here). Next, look inside both ends of the hose—if you see anything blocking airflow, carefully remove it and discard it properly. Finally, reattach your hose per the instructions above and test your machine again. 

Conclusion

We hope you have found this guide on how to clean a Dyson vacuum helpful. It is important to keep your vacuum cleaner to maintain its performance and extend its life.

Follow the tips we’ve outlined and your vacuum will be running like new in no time!